We'll go more in depth on each of these parts in Chapter 3, Choosing Your Components. For now, let's get acquainted with what makes up a multicopter.
Multicopter frames come in all shapes and sizes, from basic quadrocopters to eight-bladed monster octocopters. They are available for a wide variety of prices too. Sometimes, large frames that cost more are really better. However, this is rare indeed. We will give you more details later, but note that before you choose any components, you should have your purpose in mind. Bigger is not always better, and smaller can't carry much weight. In the following image, you can see a hexacopter frame that retails for under 100 USD and can carry quite a bit of weight. Of course, the components required to fly such a beast can cost you well over 3000 USD (not including the batteries).
Motors and propellers are the main propulsion systems for your multicopter. It's truly where the rubber meets the road. These components are, by far, under the greatest strain of any component of your multicopter. Every ounce of weight that your multicopter carries rests on the blades of the propellers. So, as you can tell, strength is a prerequisite.
The bigger are the blades, the more lift there is. However, the bigger the blades, the more is the leverage placed upon the hub of the blades and more strain is exerted. Skimp on the blades and they'll snap, and your whole investment comes crashing to the ground.
Also, the bigger the blade, the stronger the motor must be in order to counteract the torque required to turn the blade. It might seem like the motor doesn't truly have to deal with a lot of resistance. But that's just not true. If a propeller is moving enough air to lift a couple-dozen pounds into the air, there is a lot of wind resistance that the motor must counteract. Faster motors are weaker. It's a giant balancing act to figure out how to get the right blades, motors, and so on, to lift your payload for the longest time possible.
The following image shows carbon fiber blades attached to motors that spin at 480 RPM per volt (KV):
The electronic speed control
The electronic speed control (ESC) is a marvelous invention. This truly makes flying multicopters possible. Electric motors require more voltage to start spinning than to keep spinning at their lowest speed. Also, as you apply more voltage, they don't necessarily speed up on an even curve. The ESC spikes the voltage to start the motor and eases it back to keep them spinning at a low speed on a low throttle. Also, as you apply more throttle input, the ESC accelerates the motor evenly. Furthermore, most ESCs can be programmed to any curve you like. A real tech head can have a field day just programming ESCs. Don't let that scare you though … most ESCs are preprogrammed with the necessary settings to get you going without ever needing to dive in.
ESCs are the pass-through from battery to motor. They must be carefully balanced with the motor to give enough power to the motor and not burn out. Putting an underpowered ESC in your multicopter can cause crashes … or even fires. You must have an individual ESC for every motor. The following image shows all the six ESCs tied down to the hub of this multicopter:
The guidance system (the brain)
Now this is where the real magic happens. To fly a multicopter, it literally takes tens-of-thousands of calculations per second to sense whether you're going up or down or whether you are moving, tilting, or rotating, all the while adjusting your motors to counteract these forces to keep your multicopter stable. There are several aspects to the guidance system.
Most guidance systems have the same set of sensors nowadays. The main difference from system to system is how fast the calculations are done and the algorithms that are used in the firmware. Yes … I said firmware. These are literally flying computers.
In the following image, you can see the three main components of the DJI WooKong-M guidance system (this system has been the industry standard for multicopters for several years, so we'll use it as an example):
The circular module in the given image is a dual-purpose antenna. It senses both the direction (using a compass) and the GPS location (by using a 6-12 satellite lock system). This provides extremely accurate positional data for the brain to do its work.
In the other section of the photo, you'll see two grey boxes. The one in the background is the sensor box. This includes a 3-axis accelerometer and gyros to determine the pitch, roll, and yaw movement several thousand times a second. Additionally, it contains a barometer to indicate altitude. The box in the foreground is the main brain that takes all this information and your control inputs (coming in on the left side from the radio receiver), compares that to the GPS and compass data to create an accurate impression of what the drone is doing (as well as what you wish it to do), and sends speed information to the ESCs (out on the right side), and in turn to the motors to move your drone properly and in a stable fashion. Like I said … this is where the magic happens.
Furthermore, there are more add-ons that you can get to interface with your guidance system. Camera gimbals can hook in the WooKong-M (and most other systems), and as the multicopter tilts to move, the camera can actually stay level. Also, onscreen displays (OSD) can be hooked in for your camera transmitter (allowing you to see all the telemetry, including battery life, attitude (orientation), height, and so on, on a viewing monitor while seeing what your camera sees). The following image shows the autonomous flight add-on. This unit communicates with the airborne multicopter from the ground using an iPad. You can actually click on a Google Earth map … and the multicopter will fly there. Or, you can even draw out preprogrammed flight paths. These add-ons are what truly transform a multicopter into a drone.
Camera gimbals and transmitters
The term camera gimbal is a short way of saying, "a fancy device that keeps the camera leveled and reduces vibration no matter what the multicopter does within reason." So yeah … camera gimbal is much shorter. Generally, these systems hook in to your guidance system and are tuned by the pilot (you) to work properly. Gimbals (good ones at least) are not cheap; the more weight that you want to carry and the more movement you want makes the price go up exponentially. The gimbal in the following image is capable of carrying a DSLR camera. It's made by Photoship One, and a new one retails for around 800 USD.
Furthermore, it's important to have a good transmitter. It's unheard of for any videographer to blindly shoot a video in a general direction while hoping to capture what he/she wants in a great way. It's unheard of because it's ludicrous, and the first sign that you've hired the wrong pilot. Transmitter/receiver systems are generally not all that expensive, and you can expect it to be one of the smallest investments you'll make. Be careful though. These can drain power rapidly if you get the wrong one.
Your radio is the primary interface between a human and a machine. It's important to get a good one that feels right for you. The buttons should be easy to find, and it should (above all) be reliable. FM transmitters are a way of the past. Futaba, with their FASST, and Spektrum/JR (with DSMx) are the waves of the present and future. No longer do you need to worry about competing transmitters, calling out a channel, or severe fading. The new generation of transmitters/receivers are digitally paired, and have LOS ranges in terms of miles. The following is an image of the Spektrum DX7s transmitter and the AR-8000 receiver with a satellite:
United States
Great Britain
India
Germany
France
Canada
Russia
Spain
Brazil
Australia
Singapore
Hungary
Ukraine
Luxembourg
Estonia
Lithuania
South Korea
Turkey
Switzerland
Colombia
Taiwan
Chile
Norway
Ecuador
Indonesia
New Zealand
Cyprus
Denmark
Finland
Poland
Malta
Czechia
Austria
Sweden
Italy
Egypt
Belgium
Portugal
Slovenia
Ireland
Romania
Greece
Argentina
Netherlands
Bulgaria
Latvia
South Africa
Malaysia
Japan
Slovakia
Philippines
Mexico
Thailand
Filter
