The pulse width modulation (PWM) module is essentially used to generate a square wave signal at a fixed frequency, and then vary its duty cycle. It gives us the ability to accurately generate pulses of a configured duration, repeating at a configured frequency. Like the GPIO module, the PWM module on the BeagleBone Black operates at 3.3V. These PWM signals can be used to control servo motors, vary the speed of DC motors and the brightness of LEDs, and with some additional external components they can be used to generate varying voltages.

Universal asynchronous receiver/transmitter

The universal asynchronous receiver/transmitter (UART) modules are used to transmit and receive RS-232 style serial signals, which is an industry standard for serializing and transferring information between two devices using a pair of unidirectional digital signals. They can be used to communicate with PCs, Bluetooth and Wi-Fi radio modules, and GPS receivers. The BeagleBone Black's UART modules also operate at 3.3V.

Serial peripheral interface

The serial peripheral interface (SPI) module is used to communicate over SPI, which is another industry standard serial protocol. Whereas UARTs are generally used to connect two devices, SPI is made to connect one master device to one or many slave devices. It is commonly used on devices such as small character and graphics LCD screens, external ADCs, and DACs (Digital-to-Analog converters), as well as on many different types of sensor. The BeagleBone Black's SPI modules operate at 3.3V as well.

Inter-Integrated Circuit

Inter-Integrated Circuit (I2C) is yet another industry standard serial protocol. It also allows a master device to communicate with a bus of many slave devices, but it requires fewer pins than SPI. It is commonly used by real-time clocks (RTCs), as well as in many types of sensors, including Micro-Electro-Mechanical Systems (MEMS) devices, such as accelerometers, magnetometers, and gyroscopes. The BeagleBone's I2C modules operate at 3.3V.

The majority of the demo programs in this book use external hardware that must be purchased separately. Each time a demo program is given, which requires additional parts, they will be listed by part number and/or description. We will do our best to use the most readily available and lowest cost parts. All of the parts used can be purchased from one or more of the following resources:

The circuits in each demo will be assembled using solderless breadboard and jumper wires. Both come in many different shapes and sizes.

Breadboards and jumper wires can be purchased from any of the preceding links, and you'll probably want to start out with one standard-sized breadboard and a jumper wire kit, such as that from Adafruit:

That should provide enough breadboard space and jumper wires to assemble most, if not all, of the demo circuits in this book.

Just like with software, it is inevitable when assembling hardware that things won't always work the first time. There are many tools that can greatly reduce the time it takes to fix these problems. The most useful for the circuits in this book will be a multimeter, which is a tool that measures voltage and current, and often additional properties such as resistance, capacitance, and frequency. Both SparkFun and Adafruit carry very affordable digital multimeters. While these are not high quality measurement tools, they are certainly suitable for these circuits. Though not essential, I would highly recommend having some sort of multimeter on hand when building the circuits in this book.

More helpful than a multimeter for debugging tools such as PWM and serial protocols is an oscilloscope, which shows you a plot of voltage over time to visualize many different signals in a circuit. This is a more expensive tool, and will be less necessary for these circuits. Throughout the book, however, you will see screen captures of an oscilloscope to show various signals, and it should become evident just how helpful they can be. Again, Adafruit and SparkFun carry affordable oscilloscopes.

The BeagleBone was designed with prototyping in mind. If its shape and size look familiar to you, it's probably because the board was designed to fit inside an Altoids tin, which is great for both transportation and making custom enclosures. All of the expansion pins are broken out on to two female headers with a 2.54 mm pin pitch, which is one of the most commonly used spacings in the hobby and DIY world, and mating male header pins can easily be soldered by hand to add-on boards or wires. The board can be powered through USB or with a standard DC barrel jack, and power can also be supplied through the expansion headers.

There are a number of low-cost single-board GNU/Linux computers on the market these days, so let's take a look at how the BeagleBone Black stacks up against a couple of its most popular competitors.

The BeagleBone Black offers great performance and far more hardware expansion capabilities at about the same cost as the Edison and Raspberry Pi 2 B. That combined with its active open source community makes it a great choice for a huge variety of projects.

Another important feature of the BeagleBone is the two built-in PRU (programmable real-time unit) microcontrollers. These are built right into the AM335x CPU and are on the ARM interconnect, so they can share memory with the ARM processor as well as provide direct access to the peripherals. This means high-speed, real-time tasks can be executed on the PRUs asynchronously without any interruption from the Linux kernel. With growing kernel driver support and documentation to compile and load firmware to PRUs, and for communicating with the code running on them from GNU/Linux user space, they really set the BeagleBone apart from much of its competition. The PRUs are outside the scope of this book, but there are plenty of tutorials and examples to be found on the Web.

One of the BeagleBone Black's strong suits is the large community surrounding it.

The official site at http://beagleboard.org/ has lots of great information.

The main source for help with BeagleBone-related issues is the mailing list at https://groups.google.com/forum/#!forum/beagleboard.

There are also plenty of helpful people on the #beagle IRC channel at http://beagleboard.org/Community/Live%20Chat.

There are also many resources online that can help fill the gaps this book leaves on the electrical side. For instance, the Element14 community at http://www.element14.com/community/welcome and the EEVBlog at http://www.eevblog.com/, both contain a wealth of great material, as well as very active electronics forums.

You should now have a better understanding of what the BeagleBone has to offer, and maybe even some insight into the types of devices we will be interfacing with in later chapters.

In the next chapter, you will be plugging in your BeagleBone Black and learning how to log in and get everything we need installed and up to date.